Sole trader who repaired agricultural and industrial sheds fined after worker injuredSole trader who repaired agricultural and industrial sheds fined after worker injuredSole trader who repaired agricultural and industrial sheds fined after worker injuredSole trader who repaired agricultural and industrial sheds fined after worker injured
  • Home
  • About us
    • Who is CQMS
    • Testimonials
    • Accreditation, Certification & Memberships
    • News & Legislation
      • Recent Prosecutions
      • News Articles
      • Legislation
      • Corporate Manslaughter
    • Privacy Notice
    • FAQs
  • Consultancy
  • Safety-Scheme
  • Contact us
  • Home
  • About us
    • Who is CQMS
    • Testimonials
    • Accreditation, Certification & Memberships
    • News & Legislation
    • Privacy Notice
    • FAQs
  • Consultancy
  • Safety-Scheme
  • Contact us
✕

Sole trader who repaired agricultural and industrial sheds fined after worker injured

William Henry Swanson, trading as LTS Construction has been fined following an incident when a worker suffered serious injuries after falling through a fragile roof light of a grain store. LTS Construction has now ceased trading.

Wick Sheriff Court heard that on 25 September 2019, an employee of Mr Swanson was working on a grain store roof to remove and replace damaged cement roof sheets and fragile roof lights. He stood on a moss-covered roof light which gave way beneath his weight. He fell approximately 4.5m onto the concrete floor below. He sustained injuries to his head, ribs, pelvis and wrist. He suffers from short term memory loss and anxiety and has not worked since.

An investigation by the Health and Safety Executive (HSE) found that Mr Swanson did not have suitable measures in place to access the roof or to prevent the risk of (a) falling from the edge of the roof and (b) falling through roof lights. The accused should have considered the work at height hierarchy of control:

  • the use of mobile elevated work platforms (if practicable) to avoid working on a roof containing fragile materials, or
  • safe access to roof level, and
  • roof edge protection to have prevented falls from the eaves and gable wall sections of the roof, and
  • safety nets to have reduced fall risks when removing and replacing roof sheets, and
  • the use of staging or crawling boards to spread the weight of persons who worked on areas of the roof that were fragile.

None of these measures were in place at the time of the accident.

William Henry Swanson of Watten, Wick, Caithness KW1 5UP pleaded guilty to breaching the Work at Height Regulations 2005, Regulation 4(1)(a) and (c) and the Health and Safety at Work etc. Act 1974, Section 33(1)(c). He was fined £2,000.

After the hearing, HSE inspector, Liz Hunter said: “Those in control of working at height have a responsibility to implement safe work methods and to lead by example. They should communicate the work method clearly with the workers to demonstrate how fall risks will be prevented or reduced when working on or near fragile roof lights.

“Falls from height remain one of the most common causes of work-related fatalities in this country. I have investigated numerous fatal and serious accidents caused by falls through fragile roof materials during construction and maintenance activities on farm buildings. The life changing injuries sustained by Mr Swanson’s employee were preventable had a combination of safe access, roof edge protection, staging and safety nets been used by trained personnel.”

Source HSE Website 04/10/2021

Share

Related posts

27th April 2022

Soft furnishings company fined after employee injured by unguarded machinery


Read more
27th April 2022

Food manufacturing company fined after worker falls from ladder


Read more
27th April 2022

Priory Healthcare Ltd pleads guilty following HSE investigation


Read more

Get in touch

CQMS Limited
The Annexe, The Maltings, Grantham, Lincolnshire NG31 6BH
Tel: 01476 566665
Email: enquiries@cqms-ltd.com

Connect with us on social media

CQMS Safety-Scheme is a UKAS-accredited Type C Inspection Body under ISO 17020:2012 for the provision of health and safety assessment services’
CQMS Safety-Scheme - UKAS-accredited Type C Inspection Body under ISO 17020:2012

Search our site

✕

External Links

H&S Executive Website
Incident Contact Centre
The British Safety Council
RoSPA

© 2017 - 2022 CQMS Limited | All rights reserved | Site built & hosted by GIGER MEDIA | Content managed by CQMS